Nail Gun Safety 3

6 Steps to Nail Gun Safety

6 Steps to Nail Gun Safety

Here are the 6 steps to nail gun safety:

➊ Use the full sequential trigger

➊ Use the full sequential trigger

The full sequential trigger is always the safest trigger mechanism for the job. It reduces the risk of unintentional nail discharge and double fires including injuries from bumping into co-workers.

• At a minimum, provide full sequential trigger nailers for placement work where the lumber needs to be held in place by hand. Examples include building walls and nailing blocking, fastening studs to plates and blocks to studs, and installing trusses. Unintended nail discharge is more likely to lead to a hand or arm injury for placement work compared to flat work, where the lumber does not need to be held in place by hand. Examples of flat work include roofing, sheathing, and subflooring.
• Consider restricting inexperienced employees to full sequential trigger nail guns starting out. Some contractors using more than one type of trigger on their jobs color-code the nail guns so that the type of trigger can be readily identified by workers and supervisors.
• Some contractors have been reluctant to use full sequential triggers fearing a loss of productivity. How do the different types of triggers compare? 

The one available study had 10 experienced framers stick-build two identical small (8 ft x 10 ft) wood structures—one using a sequential trigger nail gun and one using a contact trigger nail gun. Small structures were built in this study so that there would be time for each carpenter to complete two sheds. 

Average nailing time using the contact trigger was 10% faster, which accounted for less than 1% of the total building time when cutting and layout was included.11 However, in this study the trigger type was less important to overall productivity than who was using the tool; this suggests productivity concerns should focus on the skill of the carpenter rather than on the trigger.

Although the study did not evaluate framing a residence or light commercial building, it shows that productivity is not just about the trigger. The wood structures built for the study did include common types of nailing tasks (flat nailing, through nailing, toe-nailing) and allowed comparisons for both total average nailing time and overall project time. The study did not compare productivity differences for each type of nailing task used to build the sheds.

➋ Provide training

➋ Provide training

Both new and experienced workers can benefit from safety training to learn about the causes of nail gun injuries and specific steps to reduce them. Be surethat training is provided in a manner that employees can understand. Here is a list of topics for training:

• How nail guns work and how triggers differ.
• Main causes of injuries – especially differences among types of triggers.
• Instructions provided in manufacturer tool manuals and where the manual is kept.
• Hands-on training with the actual nailers to be used on the job. This gives each employee an opportunity to handle the nailer and to get feedback on topics such as:
• How to load the nail gunHow to operate the air compressorHow to fire the nail gunHow to hold lumber during placement workHow to recognize and approach ricochet-prone work surfacesHow to handle awkward position work (e.g., toe-nailing and work on ladders)How best to handle special risks associated with contact and single actuation triggers such as nail gun recoil and double fires. For example, coach new employees on how to minimize double fires by allowing the nail gun to recoil rather than continuing to push against the gun after it fires.
• What to do when a nail gun malfunctions.
• Training should also cover items covered in the following sections of the guidance, such as company nail gun work procedures, personal protective equipment, injury reporting, and first aid and medical treatment.

Worksite story

Worksite story

You should know

You should know

➌ Establish nail gun work procedures

➌ Establish nail gun work procedures

Contractors should develop their own nail gun work rules and procedures to address risk factors and make the work as safe as possible. Examples of topics for contractor work procedures include but are not limited to the following:

Do’s…

Do’s…

• Make sure that tool manuals for the nailers used on the job are always available on the jobsite.
• Make sure that manufacturers’ tool labels and instructions are understood and followed.
• Check tools and power sources before operating to make sure that they are in proper working order. Take broken or malfunctioning nail guns out of service immediately.
• Set up operations so that workers are not in the line of fire from nail guns being operated by co-workers.
• Check lumber surfaces before nailing. Look for knots, nails, straps, hangers, etc. that could cause recoil or ricochet.
• Use a hammer or positive placement nailer when nailing metal joinery or irregular lumber.
• For placement work, keep hands at least 12 inches away from the nailing point at all times. Consider using clamps to brace instead of your hands.
• Always shoot nail guns away from your body and away from co-workers.
• Always disconnect the compressed air when:
• Leaving a nailer unattended;Travelling up and down a ladder or stairs;Passing the nail gun to a co-worker;Clearing jammed nails;Performing any other maintenance on the nail gun.

• Recognize the dangers of awkward position work and provide extra time and precautions:
• Use a hammer if you cannot reach the work while holding the nailer with your dominant hand.Use a hammer or reposition for work at face or head height. Recoil is more difficult to control and could be dangerous.Use a hammer or full sequential trigger nailer when working in a tight space. Recoil is more difficult to control and double fires could occur with contact triggers.Take extra care with toe-nailing. Nail guns can slip before or during firing because the gun cannot be held flush against the work piece. Use a nail gun with teeth on the safety contact to bite into the work piece to keep the gun from slipping during the shot. Use the trigger to fire only after the safety contact piece is positioned.
• Recognize the dangers of nail gun work at height and provide extra time and precautions:
• Set up jobs to minimize the need for nailing at height.Consider using scaffolds instead of ladders.If work must be done on ladders, use full sequential trigger nailers to prevent nail gun injuries which could occur from bumping a leg while climbing up or down a ladder.Position ladders so you don’t have to reach too far. Your belt buckle should stay between the side rails when reaching to the side.Maintain three points of contact with the ladder at all times to prevent a fall—this means that clamps may need to be used for placement work. Holding a nailer in one hand and the work piece with the other provides only two points of contact (your feet). Reaching and recoil can make you lose your balance and fall. Falls, especially with contact trigger nailers, can result in nail gun injuries.

Don’ts…

Don’ts…

• Never bypass or disable nail gun safety features. This is strictly prohibited. Tampering includes removing the spring from the safety-contact tip and/or tying down, taping or otherwise securing the trigger so it does not need to be pressed. Tampering increases the chance that the nail gun will fire unintentionally both for the current user and anyone else who may use the nail gun. Nail gun manufacturers strongly recommend against tampering and OSHA requires that tools be maintained in a safe condition. There is NO legitimate reason to modify or disable a nail gun safety device.
• Encourage your workers to keep their fingers off the trigger when holding or carrying a nail gun. If this is not natural, workers should use a full sequential nail gun or set down the nailer until they begin to nail again.
• Never lower the nail gun from above or drag the tool by the hose. If the nail-gun hose gets caught on something, don’t pull on the hose. Go find the problem and release the hose.
• Never use the nailer with the non-dominant hand.

➍ Provide Personal Protective Equipment (PPE)

➍ Provide Personal Protective Equipment (PPE)

Safety shoes, which help protect workers’ toes from nail gun injuries, are typically required by OSHA on residential construction sites. In addition, employers should provide, at no cost to employees, the following protective equipment for workers using nail guns:

• Hard hats
• High Impact eye protection – safety glasses or goggles marked ANSI Z87.1
• Hearing protection – either earplugs or earmuffs

Possible Consequences of Using a Nail Gun Incorrectly

➎ Encourage reporting and discussion of injuries and close calls

➎ Encourage reporting and discussion of injuries and close calls

Studies show that many nail gun injuries go unreported. Employers should ensure that their policies and practices encourage reporting of nail gun injuries. Reporting helps ensure that employees get medical attention (see #6 below). It also helps contractors to identify unrecognized job site risks that could lead to additional injuries if not addressed. Injuries and close calls provide teachable moments that can help improve crew safety.

If you have a safety incentive program, be sure that it does not discourage workers from reporting injuries. Employers that intentionally underreport work-related injuries will be in violation of OSHA’s injury and illness recordkeeping regulation.

Worksite Story

Worksite Story

➏ Provide first aid and medical treatment

➏ Provide first aid and medical treatment

Employers and workers should seek medical attention immediately after nail gun injuries, even for hand injuries that appear to be minimal. Studies suggest that 1 out of 4 nail gun hand injuries can involve some type of structural damage such as bone fracture.13 Materials such as nail strip glue or plastic or even clothing can get embedded in the injury and lead to infection. Barbs on the nail can cause secondary injury if the nail is removed incorrectly. These complications can be avoided by having workers seek immediate medical care.

A Word about Other Hazards

A Word about Other Hazards

**Air pressure. **

Pneumatic tools and compressor use are regulated under OSHA’s Construction standard at 29 CFR 1926.302(b). The provisions in this standard that are relevant for nail guns are provided below.

(1) Pneumatic power tools shall be secured to the hose or whip by some positive means to prevent the tool from becoming accidentally disconnected.

Note: An OSHA letter of interpretation14 allows the use of a quick disconnect with a pull-down sleeve to meet this requirement. It is composed of a male fitting (connector) and female fitting (coupling) that has a sleeve which must be pulled away from the end of the hose to separate the two fittings to prevent the tool from becoming accidentally disconnected. (3) All pneumatically driven nailers, staplers, and other similar equipment provided with automatic fastener feed, which operate at more than 100 p.s.i. pressure at the tool shall have a safety device on the muzzle to prevent the tool from ejecting fasteners, unless the muzzle is in contact with the work surface.

(5) The manufacturer’s safe operating pressure for hoses, pipes, valves, filters, and other fittings shall not be exceeded.

(6) The use of hoses for hoisting or lowering tools shall not be permitted.

Noise.

Noise.

Pneumatic nail guns produce short (less than a tenth of a second in duration) but loud “impulse” noise peaks: one from driving the nail and one from exhausting the air. Most nail gun manufacturers recommend that users wear hearing protection when operating a nailer.

Available information indicates that nail gun noise can vary depending on the gun, the work piece, air pressure, and the work setting. The type of trigger system does not appear to affect the noise level. Peak noise emission levels for several nailers ranged from 109 to 136 dBA.15,16 These loud short bursts can contribute to hearing loss. Employers should provide hearing protection in the form of earplugs or muffsand ensure that they are worn correctly. Employers should also ask about noise levels when buying nail guns—studies have identified ways to reduce nail gun noise and some manufacturers may incorporate noise reduction features.

Note: OSHA’s standard for exposure to continuous noise levels (29 CFR 1926.52) addresses both the noise level and the duration of exposure. In this standard, workers exposed for 15 minutes at 115 A- weighted decibels (dBA) have the same exposure as workers exposed for 8 hours at 90 dBA.The NIOSH and OSHA limit for impulse noise is 140 decibels: above this level a single exposure can cause instant damage to the ear.NIOSH recommends that an 8-hour exposure should not exceed 85 dBA and a one-second exposure should not exceed 130 dBA without using hearing protection.

Musculoskeletal disorders.

Musculoskeletal disorders.

Framing nail guns can weigh up to 8 pounds and many framing jobs require workers to hold and use these guns for long periods of time in awkward hand/arm postures. Holding an 8-pound weight for long periods of time can lead to musculoskeletal symptoms such as soreness or tenderness in the fingers, wrist, or forearm tendons or muscles. These symptoms can progress to pain, or in the most severe cases, inability to work. No studies have shown that one trigger type is any more or less likely to cause musculoskeletal problems from long periods of nail gun use. If use of a nail gun is causing musculoskeletal pain or symptoms of musculoskeletal disorders, medical care should be sought.

Conclusion

Conclusion

Nail gun injuries are painful. Some cause severe injuries or death. Nail gun injuries have been on the rise along with the increased popularity of these powerful tools. These injuries can be prevented, and more and more contractors are making changes to improve nail gun safety. Take a look at your practices and use this guide to improve safety on your job sites. Working together with tool gun manufacturers, safety and health professionals, and other organizations, we can reduce nail gun injuries.